Sewing Instructions – Model 94 Shoulder Yoke Dress (Supplement 333)

Supplement No. 333 – Model 94 Shoulder Yoke Dress (VV) ★★★ A fitted dress with front and back shoulder yokes, princess seams, set-in sleeves, a separate waistband, a flared skirt with patch pockets and an invisible zipper at the center back. Draft the pattern with the Lutterloh System from your bust and hip measurements, then add seam allowances before cutting.

Back to Supplement No. 333

To keep a PDF: use your browser's Print → Save as PDF.

What you need

Item Amount
Fabric for the dress (knit or stretch) 200 x 150 cm – 2¼ yd of 58/60″ wide fabric
Invisible zipper 24″ (60 cm)
Lightweight fusible interfacing for all facings and the zipper seam allowances (e.g. Pellon® SF101 Shape-Flex)
Invisible zipper foot for your sewing machine
Thread 1–2 spools, matching

Fabric recommendation:

  • Heavyweight rayon crepe (4.7–6.5 oz/yd²)
  • Tencel / Lyocell twill (5.0–6.8 oz/yd²)
  • Cotton sateen or poplin with some stretch (4.1–5.9 oz/yd²)
  • Linen-rayon blend (5.0–6.8 oz/yd²)
  • Lightweight wools such as wool crepe or gabardine (5.3–7.4 oz/yd²)

Fabric suggestion: sandwashed lyocell twill for a fluid, silky drape, e.g. from Stonemountain & Daughter Fabrics.

Video: How to set in a sleeve, with Mia Führer

Pattern pieces and cutting

Add ⅝″ (1.5 cm) seam allowance on all seams, 1⅝″ (4 cm) at the skirt hem and 1¼″ (3 cm) at the sleeve hems, unless your drafted pattern already includes them.

Piece Cut Interfacing
Front (A) 1 on the fold –
Front yoke (AL) 1 on the fold –
Front yoke facing (AL-ST) 1 on the fold, pattern piece mirrored Yes
Side front (AC) 2 –
Back (B) 2 –
Back yoke (BL) 2 –
Back yoke facing (BL-ST) 2 Yes
Side back (BC) 2 –
Sleeve (E) 2 –
Front skirt panel (AD) 1 on the fold –
Back skirt panel (BD) 2 –
Waistband (H) 1 on the fold –
Inner waistband (H-ST) 1 on the fold Yes
Patch pocket (AK) 2 –
Pocket opening facing (AK-ST) 2 Yes
  1. Before separating pattern pieces A and AC, and B and BC, mark a matching notch at the level of the construction cross. This makes it easier to align the fabric pieces later.
  2. Fuse lightweight interfacing to all facings, and strips of interfacing to the zipper seam allowances.
  3. Mark the end of the zipper opening on the skirt, 4¾″ (12 cm) below the waist, and pre-shrink the zipper tapes with steam.
  4. Label all 15 pieces clearly after cutting.

Sewing steps

Sew right sides together with ⅝″ (1.5 cm) seams unless noted. Finish each seam allowance right after sewing and press every seam before crossing it with another.

  1. Yokes. Pin the front yoke (AL) to the front (A), right sides together, and stitch. Finish the seam allowances together and press them up toward the yoke. Sew the back yoke (BL) to the back (B) the same way.
  2. Princess seams. Pin the front (A) to the side front (AC), right sides together, and stitch. Clip into the seam allowances along the bust curve close to the stitching and press the seams open. Sew the backs (B) and side backs (BC) together the same way.
  3. Bodice side seams. Place the front on the back, right sides together, pin along the side seams and stitch. Finish the seam allowances separately and press them open.
  4. Outer and inner waistband. On the inner waistband (H-ST), press the seam allowance along the lower edge to the wrong side. Pin the outer waistband (H) right sides together to the lower edge of the bodice, and at the same time pin the inner waistband (H-ST) with its right side to the wrong side of the bodice along the same edge, so the bodice edge is sandwiched between the two waistband layers. Pin all three layers securely. At the center back, the waistbands should end flush with the raw edges of the seam allowances; trim any excess. Stitch through all layers and press the unfinished seam allowances together down into the waistband. Press both waistbands downward.
  5. Prepare the pockets. Finish the inner edge of the interfaced pocket opening facing (AK-ST). Finish all raw edges of the pocket except the slanted opening. Pin the facing right sides together to the slanted opening edge and stitch. Press the facing upward and understitch close to the seam through the facing and seam allowances. Turn the facing to the inside and press the edge well. Prepare the second pocket the same way.
  6. Patch pockets, option A – with visible stitching. Press the seam allowances of the pockets to the wrong side. Place the pockets (AK) wrong side to the right side of the front skirt (AD), matching notch K. On the finished dress, the front edge of the pocket should line up visually with the bodice princess seam. Edgestitch along the long straight front edge and the curved lower edge. Baste the remaining raw edges to the upper skirt edge and along the side seam within the seam allowance. Or use option B:
  7. Patch pockets, option B – with invisible stitching. Place the pocket (AK) wrong side to the right side of the front skirt (AD), matching the upper notch K. Mark the front placement line on the skirt with basting thread or tailor's chalk. Remove the pocket and flip it right sides together onto the skirt, so its front seam line lies on (or just next to) the marked line. Starting at the top, stitch down to the marked stitching line of the lower pocket edge, backstitch and cut the threads. Fold the pocket back into position. Fold the seam allowance of the lower pocket edge to the wrong side and baste. Reaching into the pocket from the side seam, stitch along the lower edge from the inside as far as you can, backstitch and cut the threads. Sew the last ⅝–¾″ (1.5–2 cm) closed carefully by hand from the inside. Press the pocket edges well and baste the remaining raw edges to the upper waist edge and the side seam within the seam allowance.
  8. Skirt side seams. Place the front skirt on the back skirt, right sides together, pin the side seams and stitch. Finish the seam allowances separately and press them open. If needed, grade the seam allowances slightly in the pocket area to reduce bulk.
  9. Attach the bodice to the skirt. Place the bodice with the attached waistbands onto the skirt, right sides together, and pin the upper skirt edge to the lower edge of the outer waistband. Make sure the side seams of bodice and skirt line up, and that the princess seams form a continuous line with the front edges of the pockets. Stitch and press the seam allowances up into the waistband. Fold the inner waistband over the seam allowances and slipstitch its pre-pressed edge invisibly along the seam by hand. Finally, finish the center back seam allowances, catching both waistband layers as one.
  10. Invisible zipper in the center back.
    1. Open the zipper. Place the first zipper tape face down on the right side of the left opening edge, ¼″ (0.5 cm) from the raw edge, gently uncurling the coil as you pin. At the top, the slider stops exactly at the neckline seam line; at the bottom, the zipper extends about ¾″ (2 cm) past the marked end of the opening.
    2. Set the invisible zipper foot on the tape so the coil runs in the right groove next to the needle. Stitch from the top down to the lower opening mark.
    3. Close the zipper. Place the second tape face down on the right side of the other (right) opening edge and pin it at the top and at the waist seam at exactly the same height. Open the zipper again, set the foot so the coil runs in the left groove next to the needle, and stitch from top to bottom.
    4. Close the zipper and sew the remaining center back seam from the hem up to the zipper. Push the loose zipper end slightly aside and stitch right up to the end of the zipper stitching. Press the seam allowances open.
    Note: Inserting an invisible zipper when the side seams are already closed can be a little fiddly; keeping the shoulder seams open up to this point helps. You can also use a standard lapped or centered zipper instead.
  11. Shoulder seams. Turn the dress inside out, pin the shoulder edges together, stitch and press the seam allowances open.
  12. Neckline facing. Sew the shoulder seams of the yoke facings (AL-ST and BL-ST), press them open and finish the lower edge of the facing. Pin the facing right sides together to the neckline, starting at the center front with the shoulder seams matching exactly. Just before the center back, fold the facing edges back about ¼″ (0.5 cm) short of the zipper teeth. Fold the zipper tapes outward over the folded-back facing and pin all layers flush. Stitch around the whole neckline from one center back edge to the other. Clip the curved seam allowances every ¾″ (2 cm) close to the stitching and trim the upper corners at the zipper diagonally. Press the facing upward and understitch as far as possible. Turn the facing to the inside, shape the back neckline corners well (the top of the zipper is now neatly enclosed) and press the neckline flat. The lower edge of the facing can stay loose. Baste the side edges of the facing to the armholes just inside the seam allowance.
  13. Sleeves. Sew the underarm sleeve seams, finish the seam allowances separately and press them open over a sleeve board. Ease the upper sleeve cap with two rows of basting stitches. Pin the sleeve into the armhole, matching the underarm seam to the side seam and the sleeve cap mark to the shoulder seam. Pin smoothly up to the gathering threads and spread the ease evenly over the cap without puckers. Stitch from the sleeve side, making sure not to catch any tucks. Finish the seam allowances together and press them gently toward the sleeve.
  14. Hems. Finish the hem edges. Turn the skirt hem up 1⅝″ (4 cm) and the sleeve hems 1¼″ (3 cm), press, and sew them invisibly by hand from the inside with a blind stitch.

Tips

  • Easier zipper. Adding side seams to the waistband makes construction easier. The zipper is much easier to insert into the center back while the side seams and shoulder seams are still open.
  • Lining the dress. Cut the front (A), side fronts (AC), backs (B) and side backs (BC) – without the yokes – plus one waistband (H), the front skirt (AD) and the back skirt (BD, about 1¼″ / 3 cm shorter than the hem line) from lightweight lining fabric. Sew all lining pieces together at the princess and side seams and join bodice and skirt lining with the lining waistband. Stitch the upper edge of the lining dress right sides together to the lower edge of the yoke facings (AL-ST / BL-ST) before you attach the facings to the neckline. Then secure the lining by hand along the armholes (before setting in the sleeves) and along the zipper tapes.
  • Sleeveless version. Model 95 is the sleeveless version of this dress; it is sewn partly differently and gets its own instructions.